Adaptation clamping device

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device,
without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device,
without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device,
without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device,
without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device, without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device,
without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device,
without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device,
without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device,
without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores

Change-over from O.D. clamping to perfect I.D. clamping, without changing the clamping device? No problem with MANDO Adapt. Place the mandrel in the mounted clamping device, tighten three screws and lock the mandrel in the clamping device. In this process the mandrel engages in the coupling of the clamping device via a sophisticated mechanism, where otherwise the clamping head engages. MANDO Adapt is attractive with extreme rigidity and precision. For rotating products, run-out of 0.005 mm between chuck taper and mandrel taper can be achieved. For stationary clamping devices repeatability of 0.003 mm is possible. And best of all, this can accomplished without adjusting.

• Extremely fast conversion without detachment of the basic clamping device[1 – 2 min.]
• Large clamping range and vibration dampening due to vulcanized clamping elements
• Standard segmented clamping bushings and work-piece end-stops for machining to size available
  
  

Mandrel-in-clamping-device,
without draw bolt / pull-back

• Workpiece stabilization through axial draw force applied againstthe workpiece end-stop
• Clamping without draw bolt, consequently ideal for blind bores