Measuring equipment

A regular check of the clamping force and draw-in force is imperative for a safe, precise, and productive process. These days no one can afford to manufacture with »theoretical clamping forces/draw-in forces«. Not to mention the fact that DIN EN 1550 requires that static clamping force measurements be carried out at regular intervals. The TESTit clamping force gauge measures and records the clamping force for O.D. clamping and I.D. clamping and even the draw-in force of hollow tapered shank locations. TESTit consists of two parts: The basic unit, which is the IT module, and the measuring units, which are the TEST modules. You only need the IT module once – regardless of whether you want to measure the clamping force at O.D. clamping or I.D. clamping or the draw-in force. It is so-to-speak the basis. Depending on the measurement application, there are different TEST modules that you can easily connect to the IT module via plug & play. Even special design TEST modules fit on the IT module. All aspects have been carefully considered! With TESTit you do not leave clamping force and draw-in force up to chance; you do prevent workpiece deformation and reduce scrap.

• Clamping force measurement for O.D. and I.D. clamping
• Draw-in force measurement of hollow tapered shanks
• Two units, connected with plug & play: IT module – the basic unit, TEST module – add on for various measurement applications
• Can be used rotating [under RPM] and for stationary applications
• Software for visualization and archiving
  
  

Please note:
IT module and TEST module are available separately.
System requirements software: Operating system Windows 10, version 1709 or higher.

Scope of delivery

• IT module [basic unit], battery operating time approx. 8 h
• Measurement and archiving software [USB-Stick]
• Bluetooth® stick
• Storage case
  
  

TESTit Software

• 3 options for visualizing the measured results; bar graph, speedometer or line diagram [force / RPM diagram]
• Archive the results as .pdf or .csv file
• Bluetooth® connection for the TESTit devices

Product features

• High contrast LCD
• Operating and display unit (bezel) can be rotated through 280°
• Immediate measurements due to the Reference System
• Lifter protection cap on the measuring spindle
• Mounting shank and measuring spindle are both made of hardened stainless steel

Application
High-resolution model: Resolution 0.1 µm

Extensive measuring functions for:
- Static measurements e.g. lengths, distances and length differences
- Dynamic measurements e.g. radial run-out, straightness and flatness, by means of MAX / MIN / MAX-MIN functions

FunctionON/OFF, RESET (set display to zero), mm/inch, Reversal of counting direction, PRESET (for entering a numerical value), TOL (enter tolerance limit values), MAX/MIN memory for searching the reversal point, TIR (MAX-MIN) for testing flatness and concentricity, ABS (display can be set to zero without losing reference to preset), DATA (data transmission via connection cable), Factor (adjustable), LOCK (individual key lock)

Energy supplyBattery life approx. 3 years

Delivery scope

• instruction manual
• battery

A regular check of the clamping force and draw-in force is imperative for a safe, precise, and productive process. These days no one can afford to manufacture with »theoretical clamping forces/draw-in forces«. Not to mention the fact that DIN EN 1550 requires that static clamping force measurements be carried out at regular intervals. The TESTit clamping force gauge measures and records the clamping force for O.D. clamping and I.D. clamping and even the draw-in force of hollow tapered shank locations. TESTit consists of two parts: The basic unit, which is the IT module, and the measuring units, which are the TEST modules. You only need the IT module once – regardless of whether you want to measure the clamping force at O.D. clamping or I.D. clamping or the draw-in force. It is so-to-speak the basis. Depending on the measurement application, there are different TEST modules that you can easily connect to the IT module via plug & play. Even special design TEST modules fit on the IT module. All aspects have been carefully considered! With TESTit you do not leave clamping force and draw-in force up to chance; you do prevent workpiece deformation and reduce scrap.

• Clamping force measurement for O.D. and I.D. clamping
• Draw-in force measurement of hollow tapered shanks
• Two units, connected with plug & play: IT module – the basic unit, TEST module – add on for various measurement applications
• Can be used rotating [under RPM] and for stationary applications
• Software for visualization and archiving
  
  

Please note:
IT module and TEST module are available separately.
System requirements software: Operating system Windows 10, version 1709 or higher.

Scope of delivery

• IT module [basic unit], battery operating time approx. 8 h
• Measurement and archiving software [USB-Stick]
• Bluetooth® stick
• Storage case
  
  

TESTit Software

• 3 options for visualizing the measured results; bar graph, speedometer or line diagram [force / RPM diagram]
• Archive the results as .pdf or .csv file
• Bluetooth® connection for the TESTit devices

Product features

• High contrast LCD
• Operating and display unit (bezel) can be rotated through 280°
• Lifter protection cap on the measuring spindle
• Mounting shank and measuring spindle are both made of hardened stainless steel
• Immediate measurements due to the Reference System

Application
High-resolution model: Resolution 0.1 µm

Extensive measuring functions for static measurements e.g. lengths, distances and length differences

FunctionON/OFF, RESET (set display to zero), mm/inch, Reversal of counting direction, PRESET (for entering a numerical value), TOL (enter tolerance limit values), <0> (tolerance GO / NO GO display mode), ABS (display can be set to zero without losing reference to preset), DATA (data transmission via connection cable), Factor (adjustable), LOCK (individual key lock)

Energy supplyBattery life approx. 3 years

Delivery scope

• instruction manual
• battery

A regular check of the clamping force and draw-in force is imperative for a safe, precise, and productive process. These days no one can afford to manufacture with »theoretical clamping forces/draw-in forces«. Not to mention the fact that DIN EN 1550 requires that static clamping force measurements be carried out at regular intervals. The TESTit clamping force gauge measures and records the clamping force for O.D. clamping and I.D. clamping and even the draw-in force of hollow tapered shank locations. TESTit consists of two parts: The basic unit, which is the IT module, and the measuring units, which are the TEST modules. You only need the IT module once – regardless of whether you want to measure the clamping force at O.D. clamping or I.D. clamping or the draw-in force. It is so-to-speak the basis. Depending on the measurement application, there are different TEST modules that you can easily connect to the IT module via plug & play. Even special design TEST modules fit on the IT module. All aspects have been carefully considered! With TESTit you do not leave clamping force and draw-in force up to chance; you do prevent workpiece deformation and reduce scrap.

• Clamping force measurement for O.D. and I.D. clamping
• Draw-in force measurement of hollow tapered shanks
• Two units, connected with plug & play: IT module – the basic unit, TEST module – add on for various measurement applications
• Can be used rotating [under RPM] and for stationary applications
• Software for visualization and archiving
  
  

Please note:
IT module and TEST module are available separately.
System requirements software: Operating system Windows 10, version 1709 or higher.

Scope of delivery

• IT module [basic unit], battery operating time approx. 8 h
• Measurement and archiving software [USB-Stick]
• Bluetooth® stick
• Storage case
  
  

TESTit Software

• 3 options for visualizing the measured results; bar graph, speedometer or line diagram [force / RPM diagram]
• Archive the results as .pdf or .csv file
• Bluetooth® connection for the TESTit devices

Product features

• High contrast LCD
• Operating and display unit (bezel) can be rotated through 280°
• Immediate measurements due to the Reference System
• Lifter protection cap on the measuring spindle
• Mounting shank and measuring spindle are both made of hardened stainless steel

Application
High-resolution model: Resolution 0.1 µm

Extensive measuring functions for:
- Static measurements e.g. lengths, distances and length differences
- Dynamic measurements e.g. radial run-out, straightness and flatness, by means of MAX / MIN / MAX-MIN functions

FunctionON/OFF, RESET (set display to zero), mm/inch, Reversal of counting direction, PRESET (for entering a numerical value), TOL (enter tolerance limit values), MAX/MIN memory for searching the reversal point, TIR (MAX-MIN) for testing flatness and concentricity, ABS (display can be set to zero without losing reference to preset), DATA (data transmission via connection cable), Factor (adjustable), LOCK (individual key lock)

Energy supplyBattery life approx. 3 years

Delivery scope

• instruction manual
• battery